Previous: , Up: Netlister   [Contents][Index]

6.5 gEDA/gaf Switcap Symbols and Netlister

by: Dan McMahill

This document is released under GFDL

April 13th, 2003

The original document can be found at 

http://web.mit.edu/~geda/arch/i386_rhel3/versions/current/share/doc/geda-doc/switcap/switcap.html

The main SWITCAP page is at http://www.cisl.columbia.edu/projects/switcap/

There you can find the full reference manual of the program.

Some probably useful tips can be found at https://web.engr.oregonstate.edu/~moon/kaj/swtips.html#manual

6.5.1 Overview

This document describes the symbol library and lepton-netlist backend which supports driving SWITCAP simulations from the Lepton system. SWITCAP is a switched capacitor circuit simulator available from Columbia University. It is used in many classroom and research environments. One drawback to SWITCAP is the lack of a freely available schematic capture frontend. The Lepton SWITCAP symbol library and lepton-netlist backend tries to fill that gap.

The basic steps involved with using Lepton as the frontend for SWITCAP simulations are:

  1. Create schematics of the circuit.
  2. Create an analysis file.
  3. Extract the netlist.
  4. Run the SWITCAP simulation.
  5. Run sw2asc to extract the results.
  6. View the results with gwave.

6.5.2 Requirements

You will need the following programs to be installed:

  1. A version of Lepton EDA.
  2. SWITCAP. The executable is usually called sw. If you do not have SWITCAP available on your system, you will need to contact Columbia University to obtain a copy. The Lepton SWITCAP support was tested with SWITCAP Version A.5R Release 21-Sep-87.
  3. Although it is optional, you may wish to install a tool which can be used for plotting the output data. SWITCAP produces both ASCII data listings as well as ugly ASCII plots (note the release date of the version of SWITCAP used). Suitable tools are:
    1. Gwave. Gwave is an analog waveform viewer. It is fairly basic, but easy to use, includes cursors, and has zoom/pan features. See http://gwave.sourceforge.net/.
    2. Scilab. Similar to matlab. Powerful, but no cursors or panning. See https://www.scilab.org.
    3. Octave. Similar to matlab. See http://www.octave.org/.
    4. Grace. See http://plasma-gate.weizmann.ac.il/Grace/.

The utility sw2asc(1) mentioned above can be used to convert a SWITCAP2 output file into ASCII data files that the above GUI tools can read. It is not installed by default, you can find it in the contrib/ directory of the Lepton repository or tarball.

6.5.3 Creating Schematics

6.5.3.1 Required Symbols

This section assumes you are familiar with using lepton-schematic to create and edit schematics. SWITCAP netlisting is only supported for the components contained in the SWITCAP symbol library as well as the ground symbol found in the power library which comes with Lepton. All allowed SWITCAP elements except for subcircuits are supported. You must include the following elements on your schematic:

  1. One instance of the switcap-timing symbol. This symbol will set the master clock period for your simulations.
  2. One or more instances of the switcap-clock symbol. This symbol defines a clock with a particular phase and period. The reference designator of the clock symbol is used by the switches to set what phase they switch on.
  3. One or more instances of the switcap-analysis symbol. This symbol defines an analysis by specifying a file to include in the SWITCAP netlist. By including multiple instances of this symbol, multiple analysis files may be included.

6.5.3.2 Optional Symbols

You can also optionally add the following SWITCAP special symbols to your schematic:

  1. Zero or one instance of the switcap-title symbol. This will add a TITLE: line to the SWITCAP netlist and will appear in the output file.
  2. Zero or one instance of the switcap-options symbol. By editing the OPTIONS attribute on this symbol you can set the various options which can be passed to SWITCAP.

6.5.3.3 Net Names

When creating schematics to drive SWITCAP, you should name all nets that you wish to plot. To avoid possible conflicts with unnamed nets, you should avoid using purely numerical names for nets because all unnamed nets will be assigned (somewhat randomly) numbers without checking for possible conflicts with explicitly named nets. SWITCAP limits the length of node names to 7 characters.

6.5.3.4 Switches

When placing switches on your schematic, you will need to define which clock they are controlled with. This is done by setting the clock attribute on the switch to the reference designator of the clock which should control it.

6.5.4 Extracting the SWITCAP Netlist

To extract the SWITCAP netlist, run: 

lepton-netlist -g switcap -o test.scn file1.sch [file2.sch ...]

For the example file contained in this archive, you can run: 

lepton-netlist -g switcap -o example.scn ckt.sch clocks.sch analysis.sch

The netlist will be left in example.scn.

6.5.5 Running SWITCAP

I typically use something like: 

printf "example.scn\nexample.out\n" | sw

so I can use command history to rerun SWITCAP without having to manually type the file names each time.

Refer to the SWITCAP manual for more details.

6.5.6 Appendix A – Symbols in the Library

6.5.6.1 Capacitors (switcap-capacitor)

Ideal capacitor. Attributes:

C=capacitance

Required. Specifies filename to be included.

refdes=reference designator

Required. Must start with C and be unique.

6.5.6.2 Switches (switcap-switch)

Ideal switch. Attributes:

clock=Controlling clock

Required. Specifies which clock controls this switch.

refdes=reference designator

Required. Must start with S and be unique.

6.5.6.3 Independent Voltage Sources (switcap-vsrc)

Attributes:

refdes=reference designator

Required. Must start with V and be unique.

6.5.6.4 Dependent Voltage Sources (switcap-vcvs)

Attributes:

gain=gain

Required. Specifies the gain of the controlled source.

refdes=reference designator

Required. Must start with E and be unique.

6.5.6.5 Clock Specification (switcap-clock)

Attributes:

PSTART=starting clock phase

Required. Specifies on what phase of the master clock this clock turns on.

PSTOP=ending clock phase

Required. Specifies on what phase of the master clock this clock turns off.

PERIOD=clock period

Required. Specifies the period of the clock in terms of master clock cycles.

refdes=reference designator

Required. The switches that are controlled by this clock will refer to it by the reference designator. As such, avoid running any reference designator renumbering tools.

6.5.6.6 Master Timing Specification (switcap-timing)

Attributes:

PERIOD=clock period

Required. Specifies the period of the master clock in seconds.

Only a single instance of this symbol is allowed.

6.5.6.7 Analysis File Include (switcap-analysis)

This symbol will cause a specified file containing SWITCAP analysis commands to be included in the output netlist. Attributes:

file=filename

Required. Specifies filename to be included.

6.5.6.8 Simulation Title Specification (switcap-title)

Attributes:

TITLE=switcap title

Required. Specifies the TITLE line for the SWITCAP netlist.

Only a single instance of this symbol is allowed.

6.5.6.9 Simulation Options Specification (switcap-options)

Attributes:

OPTIONS=switcap options

Required. Specifies the OPTIONS line for the SWITCAP netlist. See the SWITCAP manual for allowed values.

Only a single instance of this symbol is allowed.

6.5.7 Example

This appendix provides a simple example of the entire process of generating a schematic, producing a SWITCAP netlist, running a simulation, and plotting the results.

ckt

Figure 6.3: Simple switched capacitor circuit

clocks

Figure 6.4: SWITCAP clock definition schematic

analysis

Figure 6.5: SWITCAP analysis definition schematic

ANALYZE SSS;
     INFREQ 100.0 1.0E6 LOG 501;
     SET V1 AC 1.0 0.0;
     PRINT VDB(OUT) VP(OUT);
     END;

ANALYZE TRAN;
     TIME 0+ 500 1
     SET V1 PULSE 0 5 10e-6 5e-6 5e-6 100e-6 500e-6;
     PRINT V(OUT);
     END;

Figure 6.6: SWITCAP analysis file, test.ana

6.5.7.1 Example Schematics

Figure 6.3 shows the schematic of a simple switched capacitor circuit. Note that some switches, S1 and S3 for example, are controlled by CLK1 while others, S2 and S4 for example, are controlled by the complement of CLK1 (#CLK1).

Figure 6.4 shows the definition of a clock and the master clock. Here we define a master clock period (mcp) of 1.0 μs in the timing block. In the clock definition symbol, we define a clock called CLK1 that has a period equal to 1 master clock period (mcp). The phase of CLK1 turning on switches is 0 and the phase of CLK1 turning off switches is 3/8 mcp. Additional clock phases can be defined by creating more instances of the clock definition symbol.

Figure 6.5 shows an instantiation of the title block symbol which will cause “my title” to be used in the TITLE line in the SWITCAP netlist. Figure 6.5 also shows an instantiation of an analysis block which directs the netlister to include the contents of the file test.ana in the output netlist.

Figure 6.6 shows the contents of the test.ana file.

6.5.7.2 Netlist the Design

To netlist the design, run: 

lepton-netlist -g switcap -o example.scn ckt.sch clocks.sch analysis.sch

6.5.7.3 Run the Simulation

Run the simulation with: 

printf "example.scn\nexample.out\n" | sw

6.5.7.4 Process the Results

Convert the SWITCAP output file to something gwave can read by running: 

sw2asc example.out

6.5.7.5 Plot the Results

Start up the gwave program and load the first sinusoidal steady state result by running: 

gwave example.out.SSS.1.asc

Drag the two waveforms onto the two waveform panels and change the x-axis to a log scale. Figure 6.7 shows the output. Start up the gwave program and load the transient result by running:

FIXME: If you have access to the SWITCAP program, please consider sending us the picture with simulation results for documentation.

Figure 6.7: Simulation Results - Sinusoidal steady state

gwave example.out.TRAN.1.asc

Drag the output waveform onto the waveform panel. Figure 6.8 shows the output.

FIXME: If you have access to the SWITCAP program, please consider sending us the picture with simulation results for documentation.

Figure 6.8: Simulation Results - Transient

6.5.8 Document Revision History

April 13th, 2003

Created switcap.tex

Previous: Forward/backward annotation between Lepton and PADS PowerPCB, Up: Netlister   [Contents][Index]